Plastic bottle of milk. One US gallon
Plastic bottles with indentations for handles
Plastic milk containers are plastic containers for storing, shipping and dispensing milk. Plastic bottles, sometimes called jugs, have largely replaced glass bottles for home consumption. Glass milk bottles have traditionally been reusable while light-weight plastic bottles are designed for single trips and plastic recycling.
Packaging of milk is regulated by regional authorities. Use of Food contact materials is required: potential food contamination is prohibited. Strict standards of cleanliness and processing must be followed.
The most common material in milk packaging is high density polyethylene (HDPE), recycling code 2. Low density polyethylene (LDPE), and polyester (PET), are also in use. Polycarbonate had been considered but had concerns about potential contamination with Bisphenol A.
Blow molded plastic milk bottles have been in use since the 1960s.
HDPE is the primary material but polyester is also used. A wide variety of milk bottle designs are available. Some have a round cross section while others have a more square or rectangular shape. A special flat-top square milk jug was recently developed to maximize shipping and storing efficiency but had some difficulties in dispensing. Many milk bottles have integral handles.
Milk bags are also in use. The milk is sold in a plastic bag and put into a pitcher for use.
Small individual containers of milk and cream are often thermoformed or injection molded and have a peelable lid. These are often used in restaurants.
The shelf life of pasteurized milk in HDPE bottles and LDPE pouches has been determined to be between 10 and 21 days when stored at 4-8 °C. Other factors such as light and temperature abuse have effects. Shelf life can be extended by
ultrapasteurisation and aseptic processing.
The indentation on the left side of a milk bottle adjusts the volume of the bottle.
Milk containers for retail sale must contain the same amount of milk as indicated on the label. To be acceptable to consumers, the containers must also appear to be completely full. Therefore, the volume of the container must be precisely controlled.
The designer of a die for a blow moulded bottle can never be completely sure of how much the finished bottle will hold. Shrinkage always occurs after the item is released from the mould. The amount of shrinkage depends upon many factors, including cycle time, inflation air pressure, time in storage prior to filling, storage temperature, and more.
A volume adjuster insert is one way to slightly adjust the volume of a bottle, without building a completely new mould. A volume insert attaches to the inside of a mould, creating a circular indentation on the side of the finished bottle. Different size inserts can be used as manufacturing circumstances change, for example mould temperature or cooling rate. The volume of finished bottles is periodically measured, and volume inserts are changed as needed.
This article is missing information about the details of a life cycle analysis. (January 2019)
Many potential factors are involved in environmental comparisons of returnable vs non-returnable systems. Researchers have often used life cycle analysis methodologies to balance the many diverse considerations. Often the comparisons show benefits and problems with all alternatives.
Reuse of bottles requires a reverse logistics system, cleaning and, sanitizing bottles, and an effective Quality Management System. A key factor with glass milk bottles is the number of cycles of uses to be expected. Breakage, contamination, or other loss reduces the benefits of returnables. A key factor with one-way recyclables is the recycling rate: In the US, only about 30-35% of HDPE bottles are recycled.
Individual plastic container of coffee creamer, Japan
11.5 fl oz, 340 mL, PETE bottle
1.4 L, 48 fl oz PETE bottle
HDPE milk bottle, 40 fl oz, 1 1/4 quart
- Gallon smashing, internet challenge involving participants deliberately spilling milk in a supermarket by breaking containers
- ^ Sidel (18 August 2018), "Many Good Reasons for Liquid Dairy to Switch to PET Packaging", Canadian Packaging, retrieved 16 September 2020
- ^ Carwile, J L (2009). "Polycarbonate Bottle Use and Urinary Bisphenol A Concentrations". Environ Health Perspect. 117 (9): 1368–1372. doi:10.1289/ehp.0900604. PMC 2737011. PMID 19750099.
- ^ US3225950A, Josephsen, "Plastic bottle", published 1965
- ^ US3152710A, Platte, "Plastic milk bottle", published 1964
- ^ US3397724A, Bolen, "Thin-walled container and method of making the same", published 1966
- ^ Galic, K (August 2018), "Packaging materials and methods for dairy applications", New Food, retrieved 11 September 2019
- ^ Petrus, R R (2010). "Microbiological Shelf Life of Pasteurized Milk in Bottle and Pouch". Journal of Food Science. 75 (1): M36-40. doi:10.1111/j.1750-3841.2009.01443.x. PMID 20492183. Retrieved 11 September 2019.
- ^ Lauren Joshi (June 2017). "Understanding Dairy Bottle Shrinkage" (PDF). Qenos. Retrieved July 28, 2019.
- ^ Spitzly, David (1997), Life Cycle Design of Milk and Juice Packaging (PDF), U.S. Environmental Protection Agency, retrieved 29 June 2014
- ^ "2016 United States National Postconsumer Plastic Bottle Recycling Report" (PDF). Association of Plastic Rcyclers. 2017. Retrieved 12 October 2018.
Books, general references